ae86 slide
31st December 2014, 01:10 AM
For sale: 4AGTE, ems 4860 ecu, custom loom, W box, tailshaft combo.
ae101 (small port) 4agze - $1700 (long motor complete, no manifolds etc)
Recently rebuilt with
ROSS forged pistons
All new ACL bearings throughout
ARP head studs
SQ engineering high flow oil pump
New water pump
Gates timing belt
T3 alloy crank pulkey
HKS 1.6mm head gasket
Head has been extensively ported and
Bigport camshafts
Motor can be heard running, all tests/inspections welcome. A lot of time and money has been spent on this motor, built to handle and flow high boost levels.
EMS 4860 ecu, full custom loom - $1200
As new ecu, custom loom to suite 4A, all braided with brand new plugs, wired by whiteys wiring, COP ignition using 3az plugs.
Steam pipe turbo exhaust manifold -$350 Suite small port 4age. High mount, T series flange (t25/28 turbo), 38mm external wastegate flange
Full 3" exhaust including dump pipe - $300 ($150 for dump pipe only)
Heat coated dump pipe to suite t series turbo. Sits very high, good for low cars, some underbody massaging required.
T28 bb Garrett turbo -$800
As new, no shaft play, comes with braided lines
Alloy custom intake manifold - $500
Comes with custom alloy vacuum box, bolts to ae86 firewall (factory bolt holes), dash 4 fitting to inlet manifold, four vacumm nipel outlets.
XF throttle body (78mm from memory)
Wrinkle finish paint, smoothed out internal runners, port matched to head
NPC brass button 212mm clutch, flywheel# - $250
Suites W series box, 4a/7a motor, used for approx 8 track days, good meat left.
4A - W series adapter plate - $100
1" thick alloy plate, adapts 4A bell housing to W gearbox
JDM bell housing (throw out fork on inlet side of engine bay) -$150
W58 gearbox- $400
Good condition, no noises, shifts fine
Gibbs custom 1 piece tailshaft - $200
W series output spline to F series diff.
Dual core alloy radiator with twin thermos on a shroud - $150
Tial 38mm wastegate, screamer pipe - $100
Will do the complete package for $5500. This is a complete turn key installation, the loom will come labelled and ready to plug into any AE/KE.
I've tried to price everything fairly, if you think its too steep, that's a shame, keep key bangin' your 4k and trying to chirp 2nd.
Located Gold Coast,
http://www.ae86drivingclub.com.au/dcimages/1/3/6/2/525251.jpg (http://s565.photobucket.com/user/ae86_slide/media/e0d9620b8e0df65725ce2c9e3e94dfc8_zps9e4d8c89.jpg.h tml)
http://www.ae86drivingclub.com.au/dcimages/1/3/6/2/556977.jpg (http://s565.photobucket.com/user/ae86_slide/media/Photo%201-09-2014%202%2050%2048%20pm_zpsfghpmyhs.jpg.html)
ae101 (small port) 4agze - $1700 (long motor complete, no manifolds etc)
Recently rebuilt with
ROSS forged pistons
All new ACL bearings throughout
ARP head studs
SQ engineering high flow oil pump
New water pump
Gates timing belt
T3 alloy crank pulkey
HKS 1.6mm head gasket
Head has been extensively ported and
Bigport camshafts
Motor can be heard running, all tests/inspections welcome. A lot of time and money has been spent on this motor, built to handle and flow high boost levels.
EMS 4860 ecu, full custom loom - $1200
As new ecu, custom loom to suite 4A, all braided with brand new plugs, wired by whiteys wiring, COP ignition using 3az plugs.
Steam pipe turbo exhaust manifold -$350 Suite small port 4age. High mount, T series flange (t25/28 turbo), 38mm external wastegate flange
Full 3" exhaust including dump pipe - $300 ($150 for dump pipe only)
Heat coated dump pipe to suite t series turbo. Sits very high, good for low cars, some underbody massaging required.
T28 bb Garrett turbo -$800
As new, no shaft play, comes with braided lines
Alloy custom intake manifold - $500
Comes with custom alloy vacuum box, bolts to ae86 firewall (factory bolt holes), dash 4 fitting to inlet manifold, four vacumm nipel outlets.
XF throttle body (78mm from memory)
Wrinkle finish paint, smoothed out internal runners, port matched to head
NPC brass button 212mm clutch, flywheel# - $250
Suites W series box, 4a/7a motor, used for approx 8 track days, good meat left.
4A - W series adapter plate - $100
1" thick alloy plate, adapts 4A bell housing to W gearbox
JDM bell housing (throw out fork on inlet side of engine bay) -$150
W58 gearbox- $400
Good condition, no noises, shifts fine
Gibbs custom 1 piece tailshaft - $200
W series output spline to F series diff.
Dual core alloy radiator with twin thermos on a shroud - $150
Tial 38mm wastegate, screamer pipe - $100
Will do the complete package for $5500. This is a complete turn key installation, the loom will come labelled and ready to plug into any AE/KE.
I've tried to price everything fairly, if you think its too steep, that's a shame, keep key bangin' your 4k and trying to chirp 2nd.
Located Gold Coast,
http://www.ae86drivingclub.com.au/dcimages/1/3/6/2/525251.jpg (http://s565.photobucket.com/user/ae86_slide/media/e0d9620b8e0df65725ce2c9e3e94dfc8_zps9e4d8c89.jpg.h tml)
http://www.ae86drivingclub.com.au/dcimages/1/3/6/2/556977.jpg (http://s565.photobucket.com/user/ae86_slide/media/Photo%201-09-2014%202%2050%2048%20pm_zpsfghpmyhs.jpg.html)