cost me $200
got all excited and chucked a wheel on.. 14 x 7.5
here some pics.
So im starting this a little early as i dont have the car yet.. untill tomorrow.
making a 3hr stip out to orange to grab a bargain Ksev, ive got heaps of inspiration for this car, ive owned one Ksev granny spec in the past and that was hell fun to drive in the wet! No power loose as suspension , ringing the neck of the poor little 4k and it heaving out a butt load of smoke to show its pain...from the tyres i wish!
EDIT:
Current Specs:
Body -
84 KE70 Flat front
Hand Flaired Guards all round
mostly Beige, random primer panels, cable ties and alluminum tape
Engine/Driveline
BT20v Head
7rib Block
Airies forged pistons
FActory GZE rods
Arp rod bolts
Arp main studs
Arp head studs
Cometic head gasket
GT 28 66 spl turbo
700cc sard injectors
BT quad throttle bodies
Hypertune planium
Hypertune intercooler with cooler plumbing
Hypertune aluminum radiator / oil cooler with 2 10 inch thermo fans.
Grex (Greddy)sandwich plate with Thermo block ( once oil is up to temp it lets the oil then flow to the oil cooler.)
extreme 5 puck ceramic clutch with lightened fly wheel
knight parts bell housing
Fresh w58 gear box
Haltech E8 computer
4 x LS1 Coils
1 Piece Tailshaft
MK11 Corona F Series
TRD 2 way
Traction Brackets
Brakes:
Front -
R32 non abs BM44 Master + R32 booster
R32 Gtst calipers
Falcon Rotors - redrilled to 4x114.3 and turned down to 280mm
Rear -
R32 gtst Twin Caliper rig - Rotor TBA
Suspension:
Front -
Coilovers
St141 base struts, Shortened
KYB AGX 4 way adj short stroke shocks
HSD Coilover kit , 8kg/mm + helpers
T3 Camber plates
T3 upper hat system
T3 33mm RCA's
T3 AE - MX conversion PS Knuckle
T3 Outer Rie rods
T3 Adj LCA
T3 Rose Joint Castor rods
Selbys 24mm adj swaybar
Custom Steering rack - around 18mm more travel then GTV
Rear:
T3 adj rose joint 4 Link
T3 adj rose Joint Panahard
TRD Blue 8 ways adj shocks
AJPS 200mm 6kg/mm springs
Wheels:
Performance Superlite GTR
15 x 10 - 12
Re001 205/50/15's
Exhaust:
38 mm tial waste gate
custom manifold with dump pipe
Twin Pipes
Interior:
Sound Deadener removed
Bride Vios III Lowmax seats
Nardi
D1 Quick release
Fuel:
JDM 86 Tank
walbro 300hp intank pump
Last edited by sundee; 22nd February 2010 at 06:54 PM.
cost me $200
got all excited and chucked a wheel on.. 14 x 7.5
here some pics.
looks like a good buy
ae71 parts for sale stripping 3xae71's and a ke70
haha! Well done, into it already!
That money offset some of the "auto to manual conversion" costs on our car, so I'm happy!
the auto box is already at the tip along with the pedal box and some other random bits n pieces
just about ready to order some stuff from ajps...
Front and rear swaybars.. selbys F - 24mm adj and R - 20mm Adj
and AJPS panhard rod
going to get my engine crain out of storage so i can take out the 3kc and get to work
update. will post pics tonight. got all the interior out, except dash top and center console, cut out some decent rust i found in the front of the pax side chasis rail. and engine is all ready to come out tomorrow.
next step i think is to get the pedal box sorted then bolt the front end in followed closly by the 4a..
need to get some dry ice tomorrow to assist removing the sound deadening
pics!!
rust cut from chasis rail
Bride in for some inspiration
rails are for an Ae86 only hole that doesnt quite line up is the rear outer.. only out by 5mm or so.. easy fix!
Did something that ive been thinking of for ages.. its kinda instant wide body KE in 5 minutes! guards will be flared after this aswell! check it
It looks like you've started with a good base for a project, but i have a few comments - some constructive, some not:
- Good on you for actually finding and cutting the rust out of the rail, not many would do that unless doing a restoration on a rotissery.
- Although I think the widebody with the slotted front guard mount holes is a nice idea, i suppose you are aware that the gap between the front guard and bonnet is going to be huge?
It'd be a better idea (in my opinion) to space the bottom of the guard out if you're having clearance issues, which it looks like you're not.
Nice idea anyway.
- Finally, that steering wheel is super homo.
Good luck with your build, i look forward to seeing it progress.
You can have any brew you want... as long as it's a Datsun / Corolla / What is that?
haha that steering wheel is going in the trash as soon as i get around to putting the nardi on! mayb u could have it? hahah jokes... the rust.. well i hate rust and it was to bad for me to leave it.. didnt take long to fix, its gone now so thats the main thing, nah not having clearance issues.. and yeah im aware of the massive bonnet gap which u can see in the photos and also i expect their to be a decent gap between the front indicator and the guard 2.. which i dont actually care about because i think its something different and i really like it.. stay tuned.. going to get my engine crain from storage today cheers Javal
jacking on grass = fail
car looks ok but